Step2Study

EPA Section 608 Universal Certification Exam practice questions

241 free questions with answers and explanations.

Practice test
  1. 51.A technician is recovering refrigerant from a high-pressure appliance. There is concern that the refrigerant may be contaminated with non-condensables. What is the primary indicator that non-condensables are present in the recovery cylinder?Type II (High-Pressure Appliances)
  2. 52.When performing a leak detection on a high-pressure appliance, which of the following methods is generally used to pinpoint the exact location of a leak after a general area has been identified?Type II (High-Pressure Appliances)
  3. 53.Which of the following refrigerants is classified as a 'very high-pressure' refrigerant under EPA Section 608 regulations?Type II (High-Pressure Appliances)
  4. 54.A technician is performing a recovery from a high-pressure appliance containing 25 pounds of R-410A. The appliance was manufactured in 2017. What is the maximum time allowed to achieve the required recovery vacuum?Type II (High-Pressure Appliances)
  5. 55.A technician is preparing to recover refrigerant from a high-pressure appliance and is concerned about protecting the vacuum pump from contamination. Which of the following is the MOST effective method to prevent oil contamination of the vacuum pump during system evacuation?Type II (High-Pressure Appliances)
  6. 56.A technician is using a self-contained (active) recovery unit to recover R-407C from a high-pressure appliance. Which of the following best describes the primary mechanism by which a self-contained recovery unit operates?Type II (High-Pressure Appliances)
  7. 57.A client reports that their high-pressure air conditioning system, which uses R-410A, is no longer cooling effectively. A technician suspects a leak and is preparing to use a leak detection method that offers the highest sensitivity for pinpointing small leaks. Which method would be MOST effective in this scenario?Type II (High-Pressure Appliances)
  8. 58.A technician is preparing to recover refrigerant from a high-pressure appliance containing 20 pounds of R-410A. The appliance was manufactured in 2005. According to EPA regulations, what is the minimum percentage of refrigerant that must be recovered if the recovery unit was manufactured after November 15, 1993?Type II (High-Pressure Appliances)
  9. 59.A technician is performing a recovery from a high-pressure appliance containing 60 pounds of R-407C. The recovery equipment was manufactured before November 15, 1993. What is the required percentage of refrigerant that must be recovered from this appliance?Type II (High-Pressure Appliances)
  10. 60.A technician is performing a major repair on a high-pressure appliance containing 10 pounds of R-407C. After recovering the refrigerant, what is the required evacuation level before recharging the system?Type II (High-Pressure Appliances)
  11. 61.A technician is performing a recovery from a high-pressure appliance containing R-22. The appliance has a charge of 35 pounds. According to EPA regulations, what is the required evacuation level if the recovery device was manufactured after November 15, 1993?Type II (High-Pressure Appliances)
  12. 62.A technician is performing a recovery from a high-pressure appliance containing R-404A. The technician observes that the recovery cylinder is significantly warmer than the ambient temperature and the pressure inside the cylinder is rising rapidly, indicating the presence of non-condensables. What is the MOST likely consequence of having non-condensables in the recovery cylinder?Type II (High-Pressure Appliances)
  13. 63.A technician is recovering refrigerant from a high-pressure appliance containing 15 pounds of R-404A. The recovery cylinder being used has a water capacity of 50 pounds. What is the maximum weight of R-404A that can be safely transferred into this recovery cylinder?Type II (High-Pressure Appliances)
  14. 64.A technician is performing a recovery from a high-pressure appliance containing R-410A. Which of the following refrigerants is classified as a 'very high-pressure' refrigerant under EPA regulations, requiring a different set of handling procedures?Type II (High-Pressure Appliances)
  15. 65.A client reports that their high-pressure air conditioning system, which uses R-410A, is not cooling effectively. A technician suspects a leak. Which of the following leak detection methods is generally considered the MOST effective for pinpointing the exact location of a small leak in an R-410A system?Type II (High-Pressure Appliances)
  16. 66.A technician is preparing to recover refrigerant from a high-pressure appliance. To minimize the release of refrigerant during connection and disconnection of hoses, what type of fittings are required by EPA regulations?Type II (High-Pressure Appliances)
  17. 67.A technician is preparing to recover refrigerant from a high-pressure appliance. To minimize refrigerant emissions, what is the MOST important practice regarding hoses and fittings?Type II (High-Pressure Appliances)
  18. 68.A technician is performing a leak test on a high-pressure system using nitrogen. The system shows a consistent pressure drop over several hours. What is the MOST appropriate next step to pinpoint the exact location of the leak?Type II (High-Pressure Appliances)
  19. 69.A technician is performing a recovery from a high-pressure appliance after a compressor burnout. Which of the following actions should the technician take to protect the vacuum pump from contamination during the evacuation process?Type II (High-Pressure Appliances)
  20. 70.A technician is evacuating a high-pressure system after a major component replacement. The goal is to dehydrate the system fully. Which of the following indicates that the system is properly dehydrated?Type II (High-Pressure Appliances)
  21. 71.A client notices a strong, pungent odor similar to ammonia near their high-pressure air conditioning system. The system uses an unknown refrigerant. What is the MOST likely refrigerant being used in this system?Type II (High-Pressure Appliances)
  22. 72.A technician is evacuating a high-pressure appliance that has undergone a major component replacement. The system contains 45 pounds of R-407C. What is the required evacuation level for this system before recharging?Type II (High-Pressure Appliances)
  23. 73.A technician is preparing to recover refrigerant from a high-pressure appliance. To ensure the safety of the recovery operation and prevent over-pressurization, what critical piece of information should be checked on the recovery unit?Type II (High-Pressure Appliances)
  24. 74.A technician is preparing to recover refrigerant from a high-pressure appliance. The appliance's data plate indicates a maximum allowable working pressure (MAWP) for the low side of 180 psig and for the high side of 350 psig. The recovery unit's MAWP is rated at 400 psig. Which of the following statements is true regarding this setup?Type II (High-Pressure Appliances)
  25. 75.Which of the following refrigerants is considered a 'very high-pressure' refrigerant under EPA Section 608 regulations?Type II (High-Pressure Appliances)
  26. 76.A technician is performing a recovery from a high-pressure appliance containing 30 pounds of R-404A. The ambient temperature is 55°F. The technician notices the recovery rate is very slow. Which of the following actions would MOST effectively increase the recovery rate?Type II (High-Pressure Appliances)
  27. 77.A technician is using a self-contained recovery unit to recover R-404A from a high-pressure appliance. The appliance has a liquid line service valve and a suction line service valve. To recover liquid refrigerant most efficiently, where should the technician connect the recovery unit?Type II (High-Pressure Appliances)
  28. 78.A technician is using a self-contained (active) recovery unit to recover R-404A from a high-pressure commercial refrigeration system. The system's compressor has failed, but the system still contains a significant amount of liquid refrigerant. Which recovery method would be MOST efficient in this scenario?Type II (High-Pressure Appliances)
  29. 79.A technician is preparing to recover refrigerant from a high-pressure appliance located outdoors on a very cold day. The recovery machine is struggling to pull a vacuum. What is the MOST effective action the technician can take to improve the recovery rate in these conditions?Type II (High-Pressure Appliances)
  30. 80.A technician is using an electronic leak detector to find a small leak in a high-pressure R-410A system. What characteristic of the leak detector is MOST important for effectively finding very small leaks?Type II (High-Pressure Appliances)
  31. 81.A technician is considering using a system-dependent (passive) recovery method for a high-pressure appliance containing R-410A. Which of the following conditions would make this method impractical or ineffective?Type II (High-Pressure Appliances)
  32. 82.A technician is preparing to recover refrigerant from a high-pressure appliance containing R-410A. The appliance contains 35 pounds of refrigerant. What is the maximum allowable time for completing the recovery if the recovery equipment was manufactured after November 15, 1993?Type II (High-Pressure Appliances)
  33. 83.A technician is performing a system-dependent (passive) recovery on a high-pressure appliance. Which of the following is a critical factor for the successful operation of this method?Type II (High-Pressure Appliances)
  34. 84.A technician is performing a major repair on a high-pressure appliance that contains R-407C. The system has 8 pounds of refrigerant. According to EPA regulations, what is the required evacuation level for this system before being returned to service?Type II (High-Pressure Appliances)
  35. 85.A technician is using a self-contained (active) recovery unit to remove R-404A from a high-pressure appliance. The ambient temperature is 40°F (4.4°C). What measure can the technician take to improve the speed of liquid refrigerant recovery?Type II (High-Pressure Appliances)
  36. 86.A technician is verifying the dehydration of a high-pressure appliance after a major repair. After pulling a vacuum, the micron gauge shows 550 microns. The technician closes the valve to the vacuum pump and monitors the system. After 15 minutes, the micron gauge reads 600 microns. What does this indicate?Type II (High-Pressure Appliances)
  37. 87.A technician is considering using a system-dependent (passive) recovery method for a high-pressure appliance. Which of the following conditions would make this method IMPRACTICAL or impossible?Type II (High-Pressure Appliances)
  38. 88.A technician is using a system-dependent (passive) recovery device to recover R-22 from a small high-pressure appliance. Which of the following is a key limitation of system-dependent recovery that might affect its efficiency?Type II (High-Pressure Appliances)
  39. 89.A technician is decommissioning a large high-pressure appliance containing 75 pounds of R-410A. According to EPA regulations for appliances with more than 50 pounds of refrigerant, what is the required timeframe for recovery after the appliance has been identified for disposal?Type II (High-Pressure Appliances)
  40. 90.A technician is performing a major repair on a high-pressure appliance containing R-410A. The system has a charge of 30 pounds. After recovery, what is the required evacuation level before recharging the system?Type II (High-Pressure Appliances)
  41. 91.A technician is preparing to recover refrigerant from a high-pressure appliance after a compressor burnout. Which of the following is the MOST important precaution to take regarding the vacuum pump during the evacuation process?Type II (High-Pressure Appliances)
  42. 92.A technician is performing a recovery from a small appliance that has a completely evacuated system due to a large leak. According to EPA regulations, which of the following actions is required?Type I (Small Appliances)
  43. 93.A technician is performing a recovery on a small appliance with a non-operating compressor. To maximize the recovery rate using a system-dependent device, which of the following actions would be most beneficial?Type I (Small Appliances)
  44. 94.A technician is preparing to recover refrigerant from a small appliance. Which of the following is NOT an acceptable method for determining the amount of refrigerant in a small appliance before beginning recovery?Type I (Small Appliances)
  45. 95.A technician is preparing to recover R-134a from a small domestic refrigerator. Which of the following statements about the recovery cylinder is most accurate?Type I (Small Appliances)
  46. 96.A technician is performing a refrigerant recovery on a small appliance. What is the maximum allowable pressure for the recovery cylinder during the recovery process?Type I (Small Appliances)
  47. 97.A technician is using a system-dependent (passive) recovery device on a small appliance with an operating compressor. To maximize the recovery rate, what action should the technician take?Type I (Small Appliances)
  48. 98.A technician is installing a new compressor in a small appliance that uses R-134a. After replacement, what is the primary purpose of evacuating the system to a deep vacuum?Type I (Small Appliances)
  49. 99.A technician is recovering R-290 (propane) from a small appliance. Which of the following is an essential safety precaution specific to working with flammable refrigerants like R-290?Type I (Small Appliances)
  50. 100.A technician is preparing to recover refrigerant from a small appliance. To prevent the intake of air and non-condensables into the recovery equipment and cylinder, what critical step should be performed immediately before connecting to the appliance?Type I (Small Appliances)